Відео

my bad.. guess at 6:29 you can full screen it.. then print screen and print it.. ect...

yeah its crazy.. .. not sure if you read the comments but turn off windows fast start for the settings to stick after you have made a profile.. Here is a updated video showing that if you need it.. ua-cam.com/video/r7zHbsZamzE/v-deo.html

hi thanks.. look in my description and just download the small package.. they both include the source.. package un touched.. .. the admin concept just came from the idea of another video i had done with a padlock .. it uses same concept of first finger being the admin .. ..

@@ModItBetter so there's no source for the amin finger from adafruit but it was your programming? Then well done. Need to have a look tomorrow since my impression is the recognition is pretty slow on first test. No idea if that's your code or normal for that sensor. Will have a look tomorrow! Thanks for this code!

@@Gorkilein its pretty simple to add it your self.. The module saves the finger print in order 1,2,3,4,5.. so basically all I did was something simple like this. if (finger.fingerID == 1) { ... thats the admin then do what ever. good luck with your project...

yes 100 percent same hardware.. only diff is the software , the price tag and sticker...Bootloader is write protected this is why you can't upgrade to any v2 firmware only the ones listed .. But updating anything comes with risks of bricking ect.. so if your ok with what you have, keep it..

I got it flying today with my new remote. V1 is realy sloppy. Im going to lash V2 now and test it tomorrow. I'll let you know the difference. I read somewhere that the V2 comes with a better GPS. Hopefully the old antenna holds up :) Thanks

@@danieldewindt3919 hopefully all goes well.. the original video is here .. forgot to answer you the first time.. ua-cam.com/video/nTyYwHtlfeg/v-deo.html its a tad more steps involved with that way..

Yes ua-cam.com/video/CPxMgzNjj0w/v-deo.html shows sonar .. It uses Sonar for low height for alt hold ect.. but will use the barometer as well for higher heights if bad readings on sonar. You can test this by flying, put Quad into alt hold then fly over a box . the quad will raise the height of the box in the air. if about 3-5 feet off ground.

@@ModItBetter Thank you very much! No one does this in our country, or everyone keeps this secret) But there is no such module anywhere! Does it just have a voltage proportional to the distance at the output? I think I'll do it on Arduino)

u can try to re install amd adrenalin and during install choose the factory reset.. are the fans or A fan actually spinning? If not try to restart the computer and watch the fans during the boot process to see if they are running or just one is. Its possible you have one fan that is not spinning and it usually happens to be the one fan that updates the pwm/fan speed to Adrenalin ..

might just have to try another pc.. if its still a problem then the chip on it is probably fried..

@@ModItBetteralso tried that bro...

yeah not much you can do.. if you have a usb to serial adapter or a adruino seeing its the ground module you could try to by pass the cp210 chip and see if you can communicate with it that way.. But i would probably just get another module............Just checked the prices ,man they went up in price since i was doing these ,use to get them for 30ish.. now they 70 and 250 ect on amazon lol.. damnnn......

@@ModItBetter Yes bro, I bought that telemetry for 90usd... That's why I keep trying to recover it... I have an Arduino bro If possible, how can I communicate telem with arduino... Can you please guide me And great thanks for your replies ❤❤

@@wk713hi.. do you still get lights on the unit at all? could be a blown regulator.. .. but anyways .. i have this video ua-cam.com/video/mTYkbxj42N4/v-deo.html its been so long... .. But basically you want to put your arduino nano into ftdi mode.. by grounding reset .. then you can use it as usb to serial device. Or you can find code for any arduino esp ect.. to do the same.. you will want to use the vcc pin on the arduino (5volts) and solder it the positive pad as I show in the video and a ground from the arduino to the ground unit. . You will also want to remove the 2 resistors like in the video and probably to be safe i would remove the yellow capacitor as well even the regulator.. something might be shorted out and back feeding .. thats if you get no lights.. Then in this part of the video i show how to connect the ground unit to receiver unit.. Follow the tx and rx accept connect the arduino tx and rx to the ground unit in those locations.. If you do this and still can't connect to the ground unit try to reverse the tx and rx on the arduino. So now instead of plugging in the ground unit usb you will plug in the arduino that connects to the ground unit.. here is the part of the video that shows rx and tx locations on the units.. ua-cam.com/video/mTYkbxj42N4/v-deo.html

your welcome .. for the past year or so i've been using one of those usb temp displays just glued it on top of my monitor so i can always know my Temps and if the fans are working or not.. Saved me about twice now..

thanks time leaving a success comment.. glad this video is still helping people..

yup @ 2:48 hall sensor.. if its even out a millimeter never mind out of the unit, it wont work heh.. glad you figured it out..

That must of been annoying to figure out, .. Thank you for taking time to leave your fix.. That will be one of my first checks now as well..

Hi its going.. work all day now for long time... How about you ? still flying lots?

thanks .. hopefully your project turns out for the best.. and thanks for taking time to leave a positive comment..

hi it actually does work if your having the same problem.. but for me on that style of mouse was only a temp fix worked maybe a day or 2. But after i pushed the encoder over and glued into place it worked fine. besides that the encoder can be full of hair ect.. couple of ppl had the rubber that goes around the wheel was actually free spinning or it could just be broken some other way. But blowing actually really works on most scroll wheel problems as your blowing out the hair and dirt from the encoder.. Sadly that is not your issue with a easy fix.

in the package i included the source.. .Try examples in that zip file.

You should find a example called ledcontrol.ino ,maybe that will see if you get the same error..

jump to 4min of the video i explain my firmware.... I also include the source code what i worked off of and other examples.. However my firmware is delete all users.. The way to delete certain users you would need to hook up to a terminal or add a key matrix and a display so you could punch in which user/id you would want to delete.. Also You would need to make a table of users names and finger id that match. .. Or if your really creative and used the chip in this video you can enable wifi and make a page so you can delete users by logging onto it with a web browser..,However you still need a table of users and id's..

@@ModItBetter oooo oke oke i was know .. thanks

yeah seems bad.. if you tried to unplug the rear camera.. and it still does it.. it could be a cable but doubtful (unless you do move your camera back and forth as well).. If its junk now it worth the time to take a look and remove the ribbon just to see if you get some life on your screen.. The processor might of over heated as well, My adas camera's I had to add little micro fans to them or they glitch out the same way as yours basically ..

Qui aurait le cablage des couleurs des moteurs sur ESC merci

Hi here is a thread on the subject.. might help you out.. forum.dji.com/thread-144143-1-1.html

Hi with a quick google..i think the robin nano is a 32bit arm chip.. this is only for all the 8bit controllers..

maybe a stlink v2 would be able to recover one.. i have bunch of those programmers but don't have a robin nano..

What a weird problem with the sd card they include.. your welcome and happy printing..=)

Hi .. You need to make a profile and save the profile.. Then load load the profile.. After that disable windows fast start. After updates and random reboots. it might still go back to zero rpm. Load your saved profile again.. So if that is not your problem ,It could be one of your fans has stopped working or needs to be cleaned out. I Had to replace fans on 570's and 580 .. You can find replacement fans on aliexpress or amazon . With the computer off flick each fan and see if it spins freely.

some accessories only work with v2 I believe.. maybe they fixed some bugs in the firmware as well.. ..Personally if your happy with yours and not getting any accessories ,just leave it be..as upgrading firmware can always be a gamble..

are you trying to have zero rpm enabled so your fans don't actually spin? If so it could very well be your gpu is just running hot and the fans will spin no matter what. You can try to do the gpu drivers again and choose factory reset during install to see if it fixes your issue. On my system I had to disable windows update drivers as it was installing older drivers on me that would conflict with amd current drivers and software but that was 6 months ago, not sure if windows fixed that issue.

cool thanks for the alternative fix as well.. I would still suggest turning off windows fast start as it works almost 100 percent of the time.. however adding your work around would probably guaranty you won't have zero rpm during game play..

Hi .. sorry I have no clue what your problem might be.. You might be better off finding a dji forum to ask your question. If this only happen after the update . You can simply revert back to the old firmware ,I show how to that at the end of the video. I only used my dji naza flight controller for about 1 hour since this video..

@@ModItBetter ok thanks

yup my 580 5700xt and 6700 all need this .. Was thinking about upgrading to the 6800.. good to know I will still have to do this.. also if you have not seen my newest video on the subject.. ua-cam.com/video/r7zHbsZamzE/v-deo.html follow this video then disable windows fast start from my newest video.. If you know how to disable windows fast start don't bother with the New video as its basically the same as this video.. , you wont have to load the profile every reboot at least.. Only updates mess with it now or the really odd system reset.

@@ModItBetter I have discovered that Aurus application doesn’t update anymore and there is a new platform that Gigabyte does. So I tried it, set fan curve manually and yesterday tried to play - the temperature was in 50-60 C (room temperature was 23C). So this application takes control over the Adrenaline edition, as Adrenaline doesn’t want to perform undervolt anymore while the Gigabyte is running… Thank you, now I’ll watch your other videos.

yeah it is annoying .. I've moved to a cheap usb display that shows my fans rpm and temps ect.. As my pc is in another room so when it does happen, I usually don't know till its too late.. If you turn off windows fast start you will only have to re load your profile once in awhile after driver or windows updates ect.. here is a video on that.. ua-cam.com/video/r7zHbsZamzE/v-deo.html

u mean the wheel it self is jammed or nothing happens at all when u move it? ... One person in the comments had a issue with the rubber just spinning on the wheel ..but that is sorta noticeable ..

also it could be stuck in media mode depending what kind of mouse you have.. but that would turn the volume up and down usually.. besides that wheel is broken/clogged with hair..ect..

your welcome.... turn off windows fast start to have your settings load during restarts.. after updates of windows or amd drivers you may have to create a new profile or re load it. If you don't know how to turn off windows fast start i made a quick step by step for that as well.. ua-cam.com/video/r7zHbsZamzE/v-deo.html

yeah lol.. my pc is in its own room so it does not bug me.. im sure the point of zero rpm is so you can play in peace while your gpu cooks.

you can see if one of your fans is not spinning right.. Only one fan controls the pwm read out for the software. I once had a wire resting on one fan. Max out the curve as well just to see if your fans go max. You can try to re install the drivers with a factor reset during driver install . I might have that picture in my description.

your welcome.. .And I'm doing fine.. every week I come up with a idea to make a video.. time just slips away from too much 9-5 work..

thanks.. .. You might be able to find a screen replacement for your mirror.. If you open it up you can look around for anything that might of came out, the ribbon might of just slipped out of its connector from vibration. worth a look unless its still working as is and your worried about totally messing it up ..